- Home
- Kits
- Kits - upgrade Tube Amp
- Dynaco MK IV & AB, ultimate MKIVi upgrade kit, auto bias for tubes ECF82, 6U8, 6GH8, 6GH8, 6F2,ECF80
Dynaco MK IV & AB, ultimate MK IVi upgrade kit, auto bias for tubes ECF82, 6U8, 6GH8, 6GH8, 6F2, ECF80
Dynaco MK IV & AB, ultimate MK IVi upgrade kit, auto bias for tubes ECF82, 6U8, 6GH8, 6GH8, 6F2, ECF80
| code: | kopie |
| Manufacturer: | TES |
| Price: | 89,00 € |
DYNACO MK4 Auto Bias
All described in the manual pdf in the "Download" section
Preparation
• Disconnect relevant wires from the original PCB driver card-reference MARK IV & AB DIAGRAM • Disconnect the connecting wire at socket 8 between tubes V2 and V3. Pins1 a 8 on sockets V2 and V3 remain connected by wire. • Disconnect the wire from the slider of the BIAS potentiometer leading to the driver.
Construction and Connecting the Auto Bias Module
• Mount the Auto Bias board with the new driver. • Connect the ground point to terminal 1 on the driver. • Connect the input to the IN terminal on the driver. • Connect the heating tubes terminals on the driver board and connect in the tube V1 to pins 4 and 5. • Connect feedback wires to terminals 3 and 7 - g2 power tube to terminal 7 and secondary OT to terminal 3 on the driver. • Connect AC power 6.3V AB to terminals 4 and 5 on the driver board • Connect CATH terminal V1 on AB to pin 1 and 8 of socket V3 • Connect CATH terminal V2 on AB to pin 1 and 8 of socket V2 • Connect GRD terminal V1 on AB to terminal 11a on the driver board • Connect GRD terminal V2 on AB to terminal 11b on the driver board • Connect the BIAS terminal on AB to the anode of the bias source rectifier
Settings
• PP stage 2 x EL34, class AB1, ultralinear: Set bias for EL34 tube. The recommended anode current in the AB1 class is 42.5 mA. 42.5 = 425 / 10.
Adjust Uref = 425 mV (0.425 V) using the Trim pot on the Auto Bias Module.
Very Important!
• DO NOT re-adjust the trim pot once the AB-D-MK IVi module is installed and wired up. The whole idea is to set it ONCE and forget it !
Goods of the same category - Dynaco MK IV & AB, ultimate MK IVi upgrade kit, auto bias for tubes ECF82, 6U8, 6GH8, 6GH8, 6F2, ECF80
ST-70 & AB, ultimate ST-70 OCTAL 6SN7 upgrade kit, auto bias INSTALLATION AND USER MANUAL FOR THE AB-Q-ST70-ST120 AUTO BIAS MODULE Introduction: This module has been designed to maintain a constant bias voltage through all power output tubes for ...
ST-70 & AB, ultimate ST-70 upgrade kit, auto bias PC-3 driver - ECF82, 6GH8, 6F2 DYNACO ST-70 - DRIVER 6GH8 ECF82, 6F2 Introduction: This module has been designed to maintain a constant bias voltage through all power output tubes for your ...
Assembled driver autobias I offer the latest autobias power driver kit. Reliable power signal for triode and pentode PP drive with four power tubes.Indication of autobias, delay of anode current growth after switching on the amplifier. Automatic ...
ST-70, PC-3 driver - ECF82, 6GH8, 6F2 DYNACO ST-70 - DRIVER 6GH8 ECF82, 6F2 Introduction: PC-3 driver board completely assembled, including tubes 6F2 (ECF82)
Dynaco MK III & AB, ultimate MK III upgrade kit, auto bias for tubes 12AU7 Amplifier installation diagram Resistor R39 in the bias source must be replaced with a value of 15 Ohm
Dynaco MK III & AB, ultimate MK III upgrade kit, auto bias for 6SN7 tubes Amplifier installation diagram Resistor R39 in the bias source must be replaced with a value of 15 Ohm
CCS Zero temperature coefficient current source SMD for tube phase Inverter completely removes the distortion caused by the heated amplifier. Suitable for drivers ST-70 VTA and other CCS inverters. Direct replacement! from ieLogical LM334Comp ...
ST-70 & AB, ultimate ST-70 VTA upgrade kit, auto bias INSTALLATION AND USER MANUAL FOR THE AB-Q-ST70-ST120 AUTO BIAS MODULE Introduction: This module has been designed to maintain a constant bias voltage through all power output tubes for your ...
