ST-70 & AB, ultimate ST-70 upgrade kit, auto bias PC-3 driver - ECF82, 6GH8, 6F2
|Price :||82,00 €|
DYNACO ST-70 - DRIVER 6GH8 ECF82, 6F2
This module has been designed to maintain a constant bias voltage through all power output tubes for your ST70 stereo power amp.
The bias is kept at a constant level on the output tubes, irrespective of the signal level.
Please note. The preset bias level for this AB-Q module, see below for details, will differ depending on whether your ST70 uses the EL34 power tubes.
6.3V AC windings for tubes are not grounded!
The kit does not contain tubes.
The advantage of using the AB-Q module is that it will extend output tube life, in a lot of cases it will also improve the sound and last but not least, you will never have to worry about adjusting the bias again.Instead of a pair of output tubes being biased together, now all four output tubes are individually biased for greater control and stability
The AB-Q module has four blue LED’s, one for each output tube, which when lit, indicate that bias is at the correct level and that all is good with each tube.
Should any of these blue LED’s go out or not go on after power up, means that here is an issue with that given output tube and that the tube in question needs to be immediately replaced.
When the amp is powered up, at first a red LED will be on, indicating that there is power to the AB-Q module. The red LED will go out after about 20s.
After a further delay of between 40-50s, each of the blue LED’s should come on indicating that the bias is now set and stable for each output tube. The amp is now ready to use.
Preparing the ST70 for the installation of a new PC-3 driver and AB-Q module:
You will need to remove the original 15.6 OHM cathode resistors and cathode connecting wires V2-V3 and V6-V7 according to the following photo.
If you want to set a different cathode current on the EL34, follow these steps:
That’s it, you just set the AB-Q module to the desired bias operating level. For EL34 Vref= 0.380V. It is set without signal.
Keep all of the above wires neat and tidy, maybe use zip ties to group them.
This now pretty much completes the wiring of the AB-Q module to the ST70 driver PC-3 pcb and the power tubes.
Double check all the wiring steps again, even triple check them
Once you are confident that all your wiring is correct and as per the above steps, it is time to test your AB-Q module installation. We are assuming that you have installed the AB-Q module into a known working ST70, not a brand new ST70, as you would need to carry out a different sequence of testing your ST70 before you should power up the AB-Q module.
Plug in all tubes, that is the driver tubes, power tubes and the tube rectifier.
Maybe stick a piece of styrofoam under one of the output transformers to cradle the ST70 chassis so that the tubes do not touch the bench top.
Connect an 8 OHM dummy load of at least 100W capacity or your speaker and if you can, short the input using a dummy RCA plug.
Power up your amp. The red LED on the AB-Q module should come on straight away and will go out after about 20s.
After an additional 40 to 50s, each of the blue LED’s on the AB-Q module should start to come on, which indicates that each output tube has reached the preset bias level and all is good. Excellent!
You can measure the actual bias voltage on each output tube with a meter just to double check.
Set you volt meter to the 1V, 2V or 5V scale in DC volts. Put the red meter lead on pin 1/8 on a power tube socket, V 2,3 ,V 6,7 and place the black meter to the chassis star ground tag. The meter should read close to 0.380V/380mV if EL34’s are used. This reading might be a little higher to start with and will get close to or exactly to the preset bias voltage as the output tubes warm up.
Do this measurement for each output tube, V2, 3, 6 and 7 , measuring at pins 1/8.
Leave the amp running for about 10 minutes, all four of the blue LED’s should remain lit.
Power down the amp and let everything cool down a bit then put the bottom chassis cover back on.
Remove the dummy RCA plug.
Place your ST70 amp in its spot, connect your speakers, RCA input and power lead to it and power the amp back up. After about a minute or so, the amps are ready for your listening session!
If things do not work as they are supposed to:
If the red LED on the AB-Q module does not come on immediately after the amp is powered up, power it back down and check the wiring/connections from pins 2 & 7 on the V3 socket to the two 6,3 AC pads on the AB-Q module. Make sure all is good there!
If none of the blue LED’s come on after the 40-50s soft start delay, power the amp back down. Check all your wiring from the AB-Q module to each of the output tube pins and to the ST70 driver pcb.
If say only three or two of the blue LED’s come on after the soft start delay, power the amp back down and check the wiring to that particular tube for which the blue LED did not go on for. Also check to make sure that the pins in that tube socket are nice and tight and that the tube fits into the socket not at all loose. Also check the pins in the tube socket of any oxidization, if they are dirty, perhaps use Deoxit or similar to clean the pins!
Do’s and don’ts:
Do check that the pins in each tube socket are tight and that each tube does not fit loosely in the socket.
Do check that the pins in each tube socket are clean of oxidization, use Deoxit or similar if they are not clean.
Good fitting and clean pins in tube sockets make ALL the difference!!
Don’t do a lot of tube rolling! This is a sure way to loosen up the pins in your sockets! If you cannot help yourself and you must do tube rolling, check the tightness of the pins each time you swap tubes!
Output from signal inverter for EL34 - 86.8 Vpp.
FFT synthesis - distortion: second harmonic frequency - 0.5%, third harmonic frequency - 0.4%
ST-70 & AB, ultimate ST-70 VTA upgrade kit, auto bias INSTALLATION AND USER MANUAL FOR THE AB-Q-ST70-ST120 AUTO BIAS MODULE Introduction: This module has been designed to maintain a constant bias voltage through all power output tubes for your ...
Dynaco MKiii & AB, ultimate MKIII upgrade kit, auto bias for 6SN7 tubes Amplifier installation diagram Resistor R39 in the bias source must be replaced with a value of 15 Ohm
Dynaco MKiii & AB, ultimate MKIII upgrade kit, auto bias for tubes 12AU7 Amplifier installation diagram Resistor R39 in the bias source must be replaced with a value of 15 Ohm
Assembled driver autobias I offer the latest autobias power driver kit. Reliable power signal for triode and pentode PP drive with four power tubes.Indication of autobias, delay of anode current growth after switching on the amplifier. Automatic ...