Number of items: 0 0,00 €

The problem boards VTA ST-70 with LM334 is solved! CCS Zero temperature coefficient current source for tube phase Inverter

CCS Zero temperature coefficient current source SMD for tube phase Inverter completely removes the distortion caused by the heated amplifier. Suitable for drivers ST-70 VTA and other CCS inverters. Direct replacement!

click to enlarge
The problem boards VTA ST-70 with LM334 is solved! CCS Zero temperature coefficient current source for tube phase Inverter TES
The problem boards VTA ST-70 with LM334 is solved! CCS Zero temperature coefficient current source for tube phase Inverter TESThe problem boards VTA ST-70 with LM334 is solved! CCS Zero temperature coefficient current source for tube phase Inverter TESThe problem boards VTA ST-70 with LM334 is solved! CCS Zero temperature coefficient current source for tube phase Inverter TES
pc
Manufacturer:TES
Price : 9,00 €
Availability:In stock
Overview of quantitative discounts
Number (pc) Price
1 +  9,00 €
10 +  5,00 €

All VTA designs using the LM334 for the Phase Inverter tail suffer thusly: long warm up time, temperature sensitivity and balance instability. This can be remedied very easily.

Due to the LM334 instability, the Phase Inverter gain constantly changes, and as a consequence, the image wanders. The amps never reach equilibrium.
At a minimum, move the compensated LM334 to the underside of the driver board. Note the orientation of the compensated LM334. On the bottom, the LM334 rounded side is toward the transformers. Mounting under the board will prevent some heating by the tubes, helping to stabilize thecompensated LM334. The current may not achieve design values quickly as the internal chassis temperature rises slowly.

For the Temperature Compensated Full Monty:

CCS parts go on the PCB underside as shown. The amp now very stable. With compensation, the LM334 stabilizes rapidly and does not drift. Sonic image now remains rock solid. Phase splitter balance is surprisingly good, tracking perfectly from naught to clipping.

Goods of the same category - The problem boards VTA ST-70 with LM334 is solved! CCS Zero temperature coefficient current source for tube phase Inverter

Dynaco MK III & AB, ultimate MK III upgrade kit, auto bias for tubes 12AU7

Dynaco MK III & AB, ultimate MK III upgrade kit, auto bias for tubes 12AU7   Amplifier installation diagram Resistor R39 in the bias source must be replaced with a value of 15 Ohm  

ST-70 & AB, ultimate ST-70 upgrade kit, auto bias PC-3 driver - ECF82, 6GH8, 6F2

ST-70 & AB, ultimate ST-70 upgrade kit, auto bias PC-3 driver - ECF82, 6GH8, 6F2   DYNACO ST-70 - DRIVER 6GH8 ECF82, 6F2   Introduction:  This module has been designed to maintain a constant bias voltage through all power output tubes for your ...

ST-70 & AB, ultimate ST-70 OCTAL 6SN7 upgrade kit, auto bias

ST-70 & AB, ultimate ST-70 OCTAL 6SN7 upgrade kit, auto bias  INSTALLATION AND USER MANUAL FOR THE AB-Q-ST70-ST120 AUTO BIAS MODULE Introduction: This module has been designed to maintain a constant bias voltage through all power output tubes for ...

Power driver with autobias for PushPull of power triodes or pentodes

Assembled driver autobias I offer the latest autobias power driver kit. Reliable power signal for triode and pentode PP drive with four power tubes.Indication of autobias, delay of anode current growth after switching on the amplifier. Automatic ...

Dynaco MK III & AB, ultimate MKIII upgrade kit, auto bias for 6SN7 tubes

Dynaco MK III & AB, ultimate MK III upgrade kit, auto bias for 6SN7 tubes   Amplifier installation diagram Resistor R39 in the bias source must be replaced with a value of 15 Ohm  

Dynaco MK IV & AB, ultimate MK IVi upgrade kit, auto bias for tubes ECF82, 6U8, 6GH8, 6GH8, 6F2, ECF80

Dynaco MK IV & AB, ultimate MK IVi upgrade kit, auto bias for tubes ECF82, 6U8, 6GH8, 6GH8, 6F2, ECF80 DYNACO MK4 Auto Bias  All described in the manual pdf in the "Download" section Preparation • Disconnect relevant wires from the original PCB ...

ST-70 & AB, ultimate ST-70 upgrade kit, auto bias

ST-70 & AB, ultimate ST-70 VTA upgrade kit, auto bias  INSTALLATION AND USER MANUAL FOR THE AB-Q-ST70-ST120 AUTO BIAS MODULE Introduction: This module has been designed to maintain a constant bias voltage through all power output tubes for your ...

ST-70 PC-3 assembled driver - ECF82, 6GH8, 6F2, including tubes 6F2

ST-70, PC-3 driver - ECF82, 6GH8, 6F2   DYNACO ST-70 - DRIVER 6GH8 ECF82, 6F2   Introduction:  PC-3 driver board completely assembled, including tubes 6F2 (ECF82)

Do you need advice? The problem boards VTA ST-70 with LM334 is solved! CCS Zero temperature coefficient current source for tube phase Inverter TES

Name, surname, company
e-mail
Phone
Your inquiry
     More information
I agree to the processing of personal data for the processing of my query




Send link to a friend

Your name
e-mail
Email your friend
Enter the code from the image antispam

We use cookies. If you continue without changing your settings, we’ll assume that you are happy to receive all cookies on the Aljancic website.   More information